- Error
Member Home
Profile
Messages
Site Tips
Deck Cleaning Contractor Directory www.deckcleaningcontractors.com
TheWoodPros Blog Posts
-
Wood Deck Cleaning & Stain ...
There are seve ...
Readmore... -
So You Want to do DIY Deck Cle ...
Part 3—Sanding and Sea ...
Readmore...
Latest Members
Latest Discussion
by thesealerstore 26 replies.
by thesealerstore 6 replies.
About Me
Basic Information
- Name
- Martin
- Company Name
- Texas Fence Savers
- Gender
-
Male
- Birthday
- 01/01/1970
- Hometown
- Keller, Texas
- About me
- Born in New Mexico lived in Colorado for the past 16 years. I am now in Keller, Tx.
Contact Information
- Mobile phone
- 682-234-5753
- Land phone
- 682-234-5753
- Address
- Po Box 1184 Keller, Texas 76244
- State
- Tx
- City / Town
- Keller
- Country
-
United States
- Website
- TxFenceSavers.com
Education
Friends
Groups
MA7319
- Karma
- Member since
- Friday, 01 January 2010 20:20
- Last online
- 2 years ago
- Profile views
- 630 views
MMI Enterprises replied to the topic Re:Floor Sanders in the forums.
Rick Petry wrote:
Lyle,
Ok, I think I've got it. Definitely a heavy rotary machine, at a 175 RPM speed. I would guess that the low RPM's would both help in preventing "burninshing" the wood and make control a bit easier. And the 60/80 grit brush can be used for both defurring and a harder "sanding".
If the weight does not hurt redwood, it certainly should not be a problem with western red cedar or especially yellow pine.
If I recall correctly, Jim sometimes uses a "middle" pad, which gives the working brush some more flex when working on uneven deck floors.
Thanks.
You may have that middle padding method via my postings elsewhere. Can just use any old basic nylon floor pad as a backup when using screen when you want some give or to help prevent screen from ripping apart or if you have no sanding driver block. Have ran these rotary machines now for over 25 years and I've yet to have need for the actual sanding driver to run the paper or screen.
Lyle,
Ok, I think I've got it. Definitely a heavy rotary machine, at a 175 RPM speed. I would guess that the low RPM's would both help in preventing "burninshing" the wood and make control a bit easier. And the 60/80 grit brush can be used for both defurring and a harder "sanding".
If the weight does not hurt redwood, it certainly should not be a problem with western red cedar or especially yellow pine.
If I recall correctly, Jim sometimes uses a "middle" pad, which gives the working brush some more flex when working on uneven deck floors.
Thanks.
You may have that middle padding method via my postings elsewhere. Can just use any old basic nylon floor pad as a backup when using screen when you want some give or to help prevent screen from ripping apart or if you have no sanding driver block. Have ran these rotary machines now for over 25 years and I've yet to have need for the actual sanding driver to run the paper or screen.
639 days ago
MMI Enterprises replied to the topic Re:A/C on Ipe in the forums.
PressurePros wrote:
When we sand ipe with a square buff its with the roughest grit available, which I think is 16. Its like a bunch of rocks glued onto paper. Even then its a slow walk, double pass for every triple set of boards.
Wow Fenner..Sanding ipe sounds tuff! Is not something I've had to do yet since strip and defur has always been swell enough prep on all the ones I ran into so far. Have you not compared the low speed swing machine to square sanders? If not I recommend doing so regardless of working with ipe or not. Have sited the differences elsewhere on ocassion as being huge due to the big swathy rotary cut being far supperior and faster than them vibrataing orbital thingies. No matter if using paper, pads, screen, or brush the rotary swing machine is like at least twice as fast. On some surfaces like dimpled urethane they are actgualy about the only solution to use besides going with a full on drum sanding procedure. Seriously try a bulky 20" and you'll be in heaven.
When we sand ipe with a square buff its with the roughest grit available, which I think is 16. Its like a bunch of rocks glued onto paper. Even then its a slow walk, double pass for every triple set of boards.
Wow Fenner..Sanding ipe sounds tuff! Is not something I've had to do yet since strip and defur has always been swell enough prep on all the ones I ran into so far. Have you not compared the low speed swing machine to square sanders? If not I recommend doing so regardless of working with ipe or not. Have sited the differences elsewhere on ocassion as being huge due to the big swathy rotary cut being far supperior and faster than them vibrataing orbital thingies. No matter if using paper, pads, screen, or brush the rotary swing machine is like at least twice as fast. On some surfaces like dimpled urethane they are actgualy about the only solution to use besides going with a full on drum sanding procedure. Seriously try a bulky 20" and you'll be in heaven.
639 days ago
Latest Video
No video uploaded yet.
My Kunena Forum Posts
MA7319 has no forum posts.
MyBlog
MA7319 has not created a blog entry yet.
JomComment
No comment made yet.
Wall
System - Kunena
MA7319 hasn't join any discussion yet.
Who is Online
0 users
and 80 guests
online
Top Members
Article Comments
Latest group walls
-
Bleach is Bad for Wood Here is my take on the Bleach topic. From what i've read over the years & some tests I did years ago... -
Armstrong Stain Club! Need Help with TheWoodPros.com capabilities? Visit this link for tips: http://www.thewoodpros.com/si... -
Armstrong Stain Club! Mark Smith's new article can be found here: http://www.thewoodpros.com/ask-the-pro/employee-pay
-
Armstrong Stain Club! armstrongstain.com is already #1 on Google for the search term "wood restoration contractor forum" N...
Member Statistics
Statistics
Total Members
: 128
Total Groups
: 3
Total Discussion
: 4
Total Albums
: 60
Total Photos
: 312
Total Videos
: 13
Total Bulletins
: 8
Total Activities
: 2131
Total Wall Posts
: 187
